Tiled Countertop DIY (No Saw Required!)Daily Interior Design Ideas

Tiled countertop DIY (click through for tutorial) We are receiving fairly close to obtaining our kitchenrenovation “finished.” I say that in quotes due to the fact we truly have a phase 1 and phase 2 plan for our kitchen renovation, but the veryfirst phase is quite a lot total. In the future, we want to get more counter and storageroom by placing in further cabinets and a peninsula for counter stools, but given that it will be a bit before we can afford to do that, we required to come up with a strategy in the meantime. The kitchen had an existing additional tall bar height peninsula with a black stone prime, but because it was so high, it was not actually useable as a kitchen operate space and we needed a lighter colourleading given that we have been staining the floorsdark. As we had to take out the peninsula anyway to install new flooring (which you may see in numerous stages of completion in the photos), we decided to minimize the current cabinets down to counter height and make a new leading for it so we could use it although we saved up for phase 2.

I have had a bit of tile knowledge making photograph boards and other modest tasks, so I decided that a tiledcountertop would look neat and clean, and, if I measured properly and utilized the correct tile, I wouldn’t even have to rent a tile noticed!

Tiled countertop DIY (click through for tutorial) This is the bar height cabinet just before it was cut down shorter. It’s hard to tell in the image, but I would have necessary a stage stool to use it for kitchen prep!

Supplies:
-woodboard reduce to sought after dimension, about 3/4″ thick (home improvement keep can cut it to size for you)
-hardy backer board and box cutter for trimming
-tile of decision (I used these large subwaytiles)
-tile grout
-tile adhesive
-tile trowel and rubber float
-tile spacers (only if making use of tile that isn’t going to come on a mesh backing)
-grout sponge
-grout haze remover (if needed)
-wood trim to frame the sides with, mine was 1 one/2″ tall and three/four” thick (house improvement retailer can minimize it to dimension for you)
-wood screws and drill

Tiled countertop DIY (click through for tutorial)Okay, in buy to make this a non-tile noticed task, I had to decide how huge of a countertop I required and then find tiles that would operate out about to individuals measurements once positioned with each other. Considering that only a single side of my countertop would face the wall and I wanted a large overhang on the side the counter stools would go on, I had a quite huge assortment of dimensions I could be inside of that would still look balanced and suit our wants. When you are looking for the appropriate tile to match your dimensions, will not overlook that the dimension the tile says on the box isn’t usually the actual measurement of the tile inside (measure it oneself) and if you are employing individual tiles rather than tiles on mesh backing, you can acquire numerous widths of spacers to make your general demotions a minor smaller or greater as necessary.

Once I had my tile and spacer size picked, I laid out all my tiles (with spacers) so I could measure out the actual size of the tiled region. You want your board and hardy backer to be the same size as your tiled location, so measure twice to be sure!

Tiled countertop DIY (click through for tutorial) Have your regional home improvement keep reduce your wood board to your tile dimensions. To cut the hardy backer, mark out your dimensions on the backer, and use a box cutter to make deep scores along those lines and then snap the pieces apart. I discover it easier to line up the scored line with the edge of a table or step and push down on the component you are snapping off. When your hardy backer is the correct dimension, location it on leading of your wooden board and use screws and a drill to secure the backer to the wood. The hardy backer has circles for every single location you should use a screw, but make certain to use screws all all around the perimeter (about one” in from the edge) so the backer does not pull away from the wood as soon as you add the tile adhesive.

Use a trowel to include a thin layer of tile adhesive to half of your board and score lines into the adhesive.

Lay the tiles onto the adhesive with your spacers in the corners. Be mindful to make positive the corners and edges are lining up correctly with the board under.

Carry on to add more adhesive and tiles till the whole board is covered. Modify any tiles as essential and let the adhesive set for 24 hrs.

Tiled countertop DIY (click through for tutorial)In situation you are wondering, “Are you certain I require the hardy backer?? Maybe I’ll just tile the wooden board…” allow this over photograph be a lesson to you. I tiled just the board on my very first attempt and the moisture from the adhesive warped the board overnight into a wonderful upside down “u” form. Dang it. Apparently the hardy backer absorbs the moisture from the adhesive and grout so the board stays straight as…properly…a board!

Tiled countertop DIY (click through for tutorial)When your adhesive is set, use the rubber float and push the grout into the spaces in between the tile until all the gaps are complete.

Tiled countertop DIY (click through for tutorial)Maintain a bucket of water and your sponge close by and swiftly wipe the grout from the tiles, acquiring off as a lot as you can. I would grout a segment, then wipe it down, and repeat till the complete board was done and then go back more than the complete issue yet again. Make confident to clean off your sponge with fresh water usually and modify out the bucket water as required. The far more grout you get off the tiles now, the less haze will continue to be on the tiles.

Allow your grout dry for 24 hrs and use a haze remover if there is nevertheless grout residue on the face of your tiles.

Tiled countertop DIY (click through for tutorial)When my tiles were set, I cut wooden trim pieces to size so I could make an outer frame about the countertop. I employed a miter saw at home so I could make the 45° angles exactly where they come together, but you can just have them make straight cuts for you at the keep if you don’t have a saw. I painted the edges, nailed them in from the sides (you can use wood screws as well), and filled any gaps in between the wood and tile with acrylic caulk. We attached the counter onto the newly painted cabinets with wood screws from the underside, screwed the cabinet into a stud on the wall (so it wouldn’t topple more than when leaned on), and we had been back in company!

Tiled countertop DIY (click through for tutorial) Tiled countertop DIY (click through for tutorial) Tiled countertop DIY (click through for tutorial) It truly is the first time in 4 months that we have had a counter height countertop once again, and it’s so wonderful to have a lot more useable space! I really like the brightness that the painted cabinet and counter adds in contrast with the dark colours that were there just before, and the tile is straightforward to wipe up and clean as essential. I feel like I find out more about doing work with tile each time I do it, so it’s good to do a bigger undertaking than I have before. And when you are renovating a residence on a budget, it truly is wonderful to have all the DIY skills you can get! xo. Laura

Credits // Author and Photography: Laura Gummerman. Photos edited with A Lovely Mess actions.

We are receiving fairly near to acquiring our kitchen renovation “finished.” I say that in estimates due to the fact we really have a phase one and phase 2 prepare for our kitchen renovation, but the first phase is fairly considerably total. In the potential, we want to get much more counter and storage space by putting in added cabinets and a peninsula for counter stools, but since it will be a bit ahead of we can afford to do that, we needed to come up with a plan in the meantime. The kitchen had an current extra tall bar height peninsula with a black stone best, but since it was so high, it wasn’t actually useable as a kitchen perform area and we desired a lighter shade leading considering that we have been staining the floors dark. As we had to take out the peninsula anyway to install new flooring (which you may see in numerous stages of completion in the pictures), we determined to lower the current cabinets down to counter height and make a new top for it so we could use it while we saved up for phase two.

I have had a bit of tile knowledge producing photo boards and other modest projects, so I decided that a tiled countertop would look neat and clean, and, if I measured appropriately and used the right tile, I would not even have to lease a tile noticed!

This is the bar height cabinet prior to it was lower down shorter. It’s difficult to inform in the picture, but I would have necessary a stage stool to use it for kitchen prep!

Supplies:
-wood board cut to sought after size, about 3/4″ thick (property improvement store can cut it to dimension for you)
-hardy backer board and box cutter for trimming
-tile of selection (I utilised these big subway tiles)
-tile grout
-tile adhesive
-tile trowel and rubber float
-tile spacers (only if utilizing tile that doesn’t come on a mesh backing)
-grout sponge
-grout haze remover (if necessary)
-wood trim to frame the sides with, mine was 1 one/2″ tall and three/4″ thick (property improvement keep can cut it to size for you)
-wood screws and drill

Ok, in order to make this a non-tile noticed project, I had to establish how massive of a countertop I required and then discover tiles that would perform out about to individuals measurements after positioned together. Because only one side of my countertop would encounter the wall and I desired a large overhang on the side the counter stools would go on, I had a quite massive variety of dimensions I could be within that would even now seem balanced and suit our demands. When you are seeking for the right tile to match your dimensions, do not overlook that the dimension the tile says on the box isn’t always the actual measurement of the tile inside (measure it oneself) and if you are utilizing person tiles rather than tiles on mesh backing, you can acquire different widths of spacers to make your overall demotions a tiny smaller or more substantial as essential.

After I had my tile and spacer dimension chosen, I laid out all my tiles (with spacers) so I could measure out the precise dimension of the tiled location. You want your board and hardy backer to be the exact same size as your tiled region, so measure twice to be sure!

Have your nearby residence improvement store lower your wood board to your tile dimensions. To lower the hardy backer, mark out your dimensions on the backer, and use a box cutter to make deep scores along individuals lines and then snap the pieces apart. I discover it less complicated to line up the scored line with the edge of a table or step and push down on the component you are snapping off. As soon as your hardy backer is the right dimension, spot it on top of your wooden board and use screws and a drill to safe the backer to the wood. The hardy backer has circles for every single location you should use a screw, but make positive to use screws all all around the perimeter (about one” in from the edge) so the backer doesn’t pull away from the wood as soon as you include the tile adhesive.

Use a trowel to add a thin layer of tile adhesive to half of your board and score lines into the adhesive.

Lay the tiles onto the adhesive with your spacers in the corners. Be mindful to make confident the corners and edges are lining up properly with the board below.

Carry on to include much more adhesive and tiles till the whole board is covered. Alter any tiles as needed and allow the adhesive set for 24 hours.

In situation you are wondering, “Are you confident I need to have the hardy backer?? Maybe I’ll just tile the wooden board…” allow this over photograph be a lesson to you. I tiled just the board on my very first consider and the moisture from the adhesive warped the board overnight into a wonderful upside down “u” form. Dang it. Apparently the hardy backer absorbs the moisture from the adhesive and grout so the board stays straight as…properly…a board!

When your adhesive is set, use the rubber float and push the grout into the spaces in between the tile right up until all the gaps are total.

Preserve a bucket of water and your sponge nearby and speedily wipe the grout from the tiles, getting off as a lot as you can. I would grout a segment, then wipe it down, and repeat till the complete board was done and then go back over the complete issue once again. Make sure to clean off your sponge with fresh water usually and adjust out the bucket water as required. The much more grout you get off the tiles now, the less haze will remain on the tiles.

Allow your grout dry for 24 hrs and use a haze remover if there is nevertheless grout residue on the face of your tiles.

When my tiles have been set, I reduce wooden trim pieces to size so I could make an outer frame all around the countertop. I utilised a miter noticed at house so I could make the 45° angles the place they come collectively, but you can just have them make straight cuts for you at the store if you will not have a noticed. I painted the edges, nailed them in from the sides (you can use wood screws also), and filled any gaps between the wood and tile with acrylic caulk. We attached the counter onto the newly painted cabinets with wood screws from the underside, screwed the cabinet into a stud on the wall (so it would not topple more than when leaned on), and we had been back in enterprise!

It really is the first time in 4 months that we have had a counter height countertop again, and it is so wonderful to have a lot more useable area! I adore the brightness that the painted cabinet and counter adds in contrast with the dark colours that were there prior to, and the tile is simple to wipe up and clean as necessary. I come to feel like I learn more about working with tile every time I do it, so it really is good to do a greater project than I have prior to. And when you are renovating a home on a pricerange, it truly is great to have all the DIY expertise you can get! xo. Laura

Credits // Writer and Photography: Laura Gummerman. Images edited with A Stunning Mess actions.

Leave a Reply

Your email address will not be published. Required fields are marked *