Convert a Cabinet into a Pull-Out Trash BinDaily Interior Design Ideas

How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Hi guys! It’s Mandi fromCreating Great in the Midwest. When we moved into our ranch house, I could not feel how significantly cabinetroom the kitchen had in contrast to the small-spaced kitchen nook in our previous apartment. I did not know what to do with all of the new space, so I’m afraid I didn’t fill the cabinets really effectively. Following living in the home for a couple of many years, I made the decision it would be a good idea to reorganize the cabinets so we could hide our trash can inside of a single. Alternatively of just putting the trash can inside of the cabinet, I rigged up this pull-out trash bin making use of drawerslide hardware. I discovered a few issues along the way, so check out my directions below if you’ve been taking into consideration doing something related in your own residence!

How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Supplies:

– Trash can with a prime lip that fits inside the cabinet (leaving at least a couple of inches all close to it)
– Full-extension drawer slide hardware (about an inch shorter than the depth of the cabinet)
– Strips of wood to mount on the within of the cabinet walls
– one/2″ plywood piece (dimension depends on cabinet size)
– Jigsaw
– Electrical power drill + drill bits
– Flat screws (size depends on the width of the strips of wood you use on the cabinet walls)
– Wood glue
– Level
– Tape measure
– Two pencils
– Sandpaper
– (optional) Wood sealer or paint

You do not want a table noticed to lower your lumber if you strategy ahead and have pieces of wood cut for you at the lumber yard or hardware shop.

Phase A single: Prepare to mount the drawer hardware. Veryfirst, you will require to remove the shelf from inside the cabinet. Mine was nailed into spot (ugh), so I had to noticed it in half and use a hammer to bang it out of area and then to pry it from in which it was nailed into the cabinet walls. Then I employed a dremmel instrument to grind off the nails.

Right after the shelves are eliminated, measure the height of your trash can and add a single inch to that measurement. Measure up from the bottom of the cabinet sides and mark the height you’ve just discovered (the trash can height plus a single inch) with a pencil. Use a degree to lengthen that line across the width of the within of the cabinet wall. You will be utilizing that line as a guidebook for putting the two strips of wood which will hold the drawer hardware.

The thickness of the wood you use to hold the drawer slide hardware depends on how far the sides of the cabinet are recessed behind the cabinet facing. My cabinet insides were recessed much less than an inch, so the lumber I got was one”x3″, each piece reduce to the length of my drawer slides. You can have the wood lower to size at the hardware retailer if you never very own a table saw (which I never!).How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Stage Two: Secure each and every of the trimmed 1″x3″ wood pieces up to the cabinet walls with four sheet metal screws. Sheet metal screws are nice since they are sharp sufficient to drive into wood with out drilling a pilot hole 1st. I nevertheless drilled pilot holes into the pieces of wood just before lining them up against the lines I had at first marked with the degree across the width of the cabinet walls, even though I did not want to drill pilot holes into the cabinet walls, thanks to the sheet metal screws. On each and every inside cabinet wall, I lined up a 1×3 so that the best of the wood was against the line I had marked, then I used masking tape to hold it into location while I drilled the sheet metal screws through the pilot holes of the 1×3 and into the cabinet wall.

Make sure the screws you use are significantly less than the width of the cabinet walls plus the width of the wood you are mounting. You will not want the sharp ends of the screws poking via the other side of the cabinet wall! If you are not utilizing sheet metal screws and want to drill pilot holes into the cabinet walls, it can be useful to mark a level on your drill bit to demonstrate in which you need to have to stop so that you do not drill completely via the cabinet wall. You can do this by placing masking tape correct onto your drill bit, as shown in the image under left.How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Phase 3: After you have mounted the wood for the drawer slide hardware, you will require to measure the actual width amongst them so you can lower the platform that the trash can will fit into. Employing a level to measure the distance can support ensure the measurement is exact. Your drawer slides should come with paperwork that tells you how a lot room they take up. The standard is one/two”, so you ought to subtract that (or the exact measurement that your paperwork says) from the width you measured, and then have your plywood cut to that width. The depth your plywood should be lower ought to be the exact same as the length of your drawer slide hardware (about one” much less than the depth of your cabinet).How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Phase 4: You will also want to reduce pieces of wood to make an apron–or sides–for the trash can platform. You will take these pieces of wood and glue them to the top plywood piece to make it more substantial and to generate a nice edge for attaching the drawer hardware to the platform. You only require 3 pieces of wood for this–a single for the front, and a single for each side. You can have these pieces reduce from the remainder of the 1×3 you utilised in measures 1 and two. Just have the piece for the front portion of the apron minimize to the actual width of the plywood piece from step 3, and then the side pieces of the apron must be reduce to the depth of the plywood piece minus the width of the front portion of the apron (most likely 1″, but examine the width to make positive!). It is going to search like the image below right after you glue those three apron pieces onto the plywood. Make sure the sides keep parallel, simply because you may be attaching drawer hardware to this, and the drawer won’t slide really nicely if it is not parallel. If you have clamps, use them to hold the wood in spot whilst the glue dries.How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Stage 5: Lay the trash can upside down onto the platform (right after the wood glue has dried) and trace all around it. My picture exhibits this becoming accomplished on the bottom side of the platform, but that was a goof on my component, simply because when I went to lower out the shape, I recognized that the jigsaw couldn’t cut the corners from the bottom of the platform because the apron received in the way. So trace the outline of your trash can on top of the platform, not underneath it.

Step Six: Hold two pencils with each other and trace close to the outline you produced in stage five. Use tape to hold the pencils together if you’re getting difficulties trying to keep them together. The aim is to transpose a line about a quarter-inch within the outline of the trash can which you will use as a manual for cutting out the form with the jigsaw in the up coming step. The smaller sized form will hold the trash can from falling through the hole.IHow to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Step Seven: Drill a hole near the newly transposed trash can outline–huge sufficient to fit the blade of your jigsaw. Insert the jigsaw and commence cutting out the hole along the line. Do not make the hole bigger than the smaller transposed trash can outline or the trash can will fall by means of it when you go to put it in place! If you are anxious about the hole getting the appropriate size, practice on a piece of cardboard 1st.How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Step Eight: Sand along the hole you just lower and knock off any sharp corners of the trash can platform. At this level you will want to seal or paint your wood however you pick. I sprayed a coat of varnish.

Stage Nine: Mount the inside part of your drawer slide hardware onto the middle of the platform sides. I drilled into the vertically-shaped hole (as shown above proper) so that if I did not get the placement of the drawer slide just proper, the hardware could simply shift up or down as soon as I slid the platform into area.How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Phase 10: Make certain the 1x3s that had been mounted onto the cabinet walls are properly parallel. If they are not, sand them down right up until they are. Also, make sure the screws holding them into location do not jut out at all–I ran into this dilemma and it was so irritating! When I drilled the pilot holes into the 1x3s in stage two, I should have employed a countersink drill bit so that the screws would be recessed and out of the way. I ended up getting to consider down these 1x3s, countersink the pilot holes, and put them back up again. Then I was capable to use the degree and hang the outside elements of the drawer slide hardware.

Following the drawer slide hardware was connected to the cabinet walls and the trash can platform, I was ready to slide the platform into area and use my trash can! Or so I believed. It turned out that the wood I glued to the platform for the apron had shifted ahead of the glue dried, which prevented the platform from becoming completely parallel. So I pulled out the platform, took off the drawer slide hardware, and sanded down the sides of the platform until finally they were parallel. Then I slid it back into location and it worked flawlessly!How to convert a cabinet into a pull-out trash bin- get that trash can out of sight!Right after using this trash can for a few days, we made a decision it would be great if the cabinet door was attached to the front of the trash can platform so that all you have to do is pull out the cabinet door, alternatively of opening it and then pulling out the trash can. Because we’re going to be painting our cabinets soon, I believe it will be the excellent time to eliminate the hinge hardware from the cabinet door and screw the door onto the trash can platform to make this handy hidden trash bin even less complicated to use!

–Mandi

Credits // Author and Photography: Mandi Johnson

Weisser Wuerfel by GiraDaily Interior Design Ideas

Weisser Wuerfel is a project completed by Gira.

The home is located in Germany.

93fa6  Weisser Wuerfel 01 850x566 Weisser Wuerfel by Gira architecture ideas 12aea  Weisser Wuerfel 02 850x509 Weisser Wuerfel by Gira architecture ideas 06568  Weisser Wuerfel 03 850x566 Weisser Wuerfel by Gira architecture ideas ee528  Weisser Wuerfel 04 850x1270 Weisser Wuerfel by Gira architecture ideas ee528  Weisser Wuerfel 05 850x566 Weisser Wuerfel by Gira architecture ideas 660b5  Weisser Wuerfel 06 850x566 Weisser Wuerfel by Gira architecture ideas 660b5  Weisser Wuerfel 07 850x566 Weisser Wuerfel by Gira architecture ideas 1467b  Weisser Wuerfel 08 850x566 Weisser Wuerfel by Gira architecture ideas 4dcea  Weisser Wuerfel 09 850x573 Weisser Wuerfel by Gira architecture ideas 4dcea  Weisser Wuerfel 10 850x566 Weisser Wuerfel by Gira architecture ideas cef5e  Weisser Wuerfel 11 850x1275 Weisser Wuerfel by Gira architecture ideas 3a16e  Weisser Wuerfel 12 850x1275 Weisser Wuerfel by Gira architecture ideas 73e92  Weisser Wuerfel 13 850x1275 Weisser Wuerfel by Gira architecture ideas 86090  Weisser Wuerfel 14 850x566 Weisser Wuerfel by Gira architecture ideas 86090  Weisser Wuerfel 15 850x566 Weisser Wuerfel by Gira architecture ideas dc022  Weisser Wuerfel 16 850x566 Weisser Wuerfel by Gira architecture ideas dc022  Weisser Wuerfel 17 850x566 Weisser Wuerfel by Gira architecture ideas ba81d  Weisser Wuerfel 18 850x562 Weisser Wuerfel by Gira architecture ideas ba81d  Weisser Wuerfel 19 850x554 Weisser Wuerfel by Gira architecture ideas 467dd  Weisser Wuerfel 20 850x538 Weisser Wuerfel by Gira architecture ideas

Weisser Wuerfel by Gira:

“Admittedly, the plot is a rarity. It is located directly in front of a nature reserve which guarantees an unobstructed view of nature, and there is a small forest with an old stock of trees in the rear. Despite this, the plot is located in the proximity of a large Bavarian city with motorway access just a few kilometres away.

However, building their dream home there wasn’t that simple for the owners. This was due to the fact that the nearly square building lot is slightly twisted and located surrounded by elongated parcels of land which have been built-up for a long time. The building shape of the residence was based on this distinctive feature: a cube with a flat roof which is fit into an ascending slope. The outdoor areas are staggered, and the spacious terraces pick up on the very linear and rigid structure, which is unusual in this area. Huge windows on the southwestern side open up the cube and allow a great deal of light to enter.

The young owners deliberately wanted to build a modern home and looked for a suitable property for years. They used the wait time in a meaningful way to collect inspirations during their travels and holidays. This included inspirations of houses with attractive architecture, as well as interior design details and accessories. It was important to the working couple that the design of the interior be spacious, airy, open and bright. “Basically, we developed the house from the inside out, and the cube shape was an almost inevitable result,” said the builder. The fact that it is energy-efficient was a further advantage.

Progress was quick once a suitable property had been found. A local construction company realised the house which had already been fully designed in the family’s minds without having to make many changes. They built a 12 x 12 metre (39 x 39 foot) structure made of classic brickwork. The ground floor is basically a single open room, apart from a guest bathroom and a pantry. An open kitchen/living room passes into the living area, which is also open-plan. They are separated only by a fireplace which is accessible from all sides. Without a doubt the home’s centrepiece is the “light tower” facing southwest and stretching up into the upper floor. There is a dominating walnut dining table here, with a magnificent designer chandelier towering above it. The delicate appearance of the sophisticated glass façade was realised with a transom/mullion structure. It allows an unobstructed view far into nature – including of the old oak tree which shelters the new home from one corner of the property.

A curved staircase – also made of walnut – leads to the upper floor which houses only bedrooms and bathroom in addition to a guest room. This area also has a full view of the natural surroundings. “A sense of space means quality of life” is the concept of the builders. It was consciously designed as a contrast to their prior living situation where although it had been large, the rooms had been small, low, and tight. Their new house is the complete opposite, and the ceiling height of nearly 3 metres makes a significant contribution here. The owners planned even more, saying, “We wanted to eliminate the separation between the indoors and outdoors as much as possible. Therefore, we realised large windows. Also, the balconies on the southern and western side lead out into the garden which is adjacent to the nature reserve, divided only by a narrow street.” In the winter, the heat generated reduces energy consumption measurably. In contrast, the house is rather sealed off towards the other two directions, which is also an energy-efficient solution.

In addition to the engineering room and home gym, there is a large garage in the cellar which opens up to the street in front of the house at ground level.

The design signature of the builders is perceptible in each detail because the long pre-planning phase allowed time for their ideas to mature. The floor-to-ceiling doors are also walnut, while all of the floors on the two residential levels are covered with large stoneware tiles which shimmer in matt anthracite. The counter and free-standing kitchen island pick up on this material and colour tone. The white walls throughout reflect light into the interior of the house. Only a raspberry-coloured colour accent in the living room relaxes this severe design.

In addition to the structure, the technical inner working of the house is also modern. The fact that the builder is a fan of technology reinforced his wishes: He explained, “I wanted to have both trend-setting and future-fit building technology in my home.” He also obtained a great deal of outside stimulation and information in this context – from magazines, as well as from the Internet. His “initial contact” with Gira was also within the virtual world. The home owner was immediately fascinated by the uniform and visually appealing Gira switches – the Gira Esprit series in black glass was installed through the entire house. He considered the possibilities for building control even more interesting because they make living more convenient, secure, and energy-efficient today. The basis for this is the powerful KNX system which links all the electrical components in the home with one another. The intelligent central control unit behind this is the Gira HomeServer, where all of the information merges and is evaluated.

An experienced professional was needed to realise a system like this – the builder was also able to find one of those on the Gira website. The solution provider in the field of modern building control runs a competence network of KNX experts, called System Integrators. The search function filtered a nearby contact person out of its comprehensive country-wide network: Anton Hieber in Schwabmünchen. The initial consultation was held in a relaxed atmosphere in his Gira Revox Studio. The System Integrator was henceforth closely included in the planning process. It was his job to realise the builder’s wishes for building technology and integrate them into a uniform, easy-to-operate system.

Security aspects were paramount in this regard. The alarm system is integrated in the KNX system while several IP cameras monitor the outdoor area and supply the images to the two Gira Control 19 Client operating panels in the living area and bedroom. The entrance area below in front of the house and the building’s rear door are also monitored with video cameras – the Gira door stations with wide-angle cameras deliver images of the areas which cannot be seen from inside the home. The Gira DCS-IP-gateway transfers the images from all the cameras to the operating panels, thus making these panels expanded home stations for door communication.

The Gira door stations installed outdoors are equipped with Keyless In functions. The Gira Keyless In Fingerprint controls access using the unique biometric properties of the human fingerprint. It acts as an electronic key, but with the advantage that it’s always available. It can’t be lost, misplaced, forgotten, stolen or copied. The home owners are particularly fascinated by the fact that different fingers can control different functions. The door communication should also be installed on mobile end devices such as iPhones and iPads in several months. Anton Hieber will integrate the new Skype expansion of the Gira DCS-IP-gateway for this purpose.

The letterbox in front of the house is also monitored. It transmits a message when mail is actually delivered and indicates exactly when that occurred. In addition, there is a central fire alarm, plus a separate Gira smoke detector in each room. The electrical control of several windows that cannot be accessed by hand is a convenient function. Security aspects also play a role here: special contacts display on the operating panels whether windows and doors are still open when the family leaves the house.

For the owners, however, modern living also meant living in a power-saving and healthy way. For example, the heating – a gas-fired boiler – is integrated in the KNX system in the form of single-room control including a comparison of target and actual figures. A ventilation system provides fresh air for the entire indoor area. It has eight adjustable levels and controls e.g. the temperature of the supply air. Anton Hieber programmed the special fireplace switching for the open fireplace. The blinds are equipped with automatic functions to shade the house ideally in the summer. They react even when the family is not home. A weather station on the roof safeguards the house against storms and hail, and the blinds are raised automatically in case of emergency. The weather station can also call up forecasts to be processed by the HomeServer from the Internet.

The lighting is mainly realised with LEDS, except for the chandelier in the light tower. This is also a construction measure to conserve energy. A photovoltaic system on the roof generates power for the home – and its current values can also be viewed on the operating panels. In addition, the entire building control can be monitored and controlled while away using an iPhone or iPad. “It is an ideal solution for owners who are away often,” said System Integrator Anton Hieber.”

Photos by: Ulrich Beuttenmüller

Weisser Wuerfel by Gira was published on HomeDSGN on Oct 13, 2014.

CATEGORIES: House • Interior Design

TAGS: Art • Bathroom • Bedroom • Contemporary House • Decorative Accessory • Dining Room • Fireplace • Germany • Gira • Hall and Entrance • Kitchen • Landscaping • Lighting • Living Room • Rug • Staircase • Wall Decor

Click any photo to see a larger image – Use buttons or j/k/arrow keys to navigate through the articles

Balsa Wood Diamond OrnamentDaily Interior Design Ideas

Diamond ornament diy abeautifulmess.com Hey, it really is Laura again! I never knowabout you, but I enjoy seeing all the amazing 3D factors individuals create with paper. There are tons of clever minor boxes and animals you can make, but I acquired additional thrilled when I identified all the gemstone templates that exist on the internet. Make my very own diamonds?! Yes please. I believed the diamond shape would make a great ornament for my Christmastree, but I didn’t think a decoration produced out of only paper would keep very properly from yr to yr. Which is where the balsa wood comes in! The wood can make the layout much sturdier and isn’t going to change the all round geometric truly feel of the diamond.Diamond suppliesSupplies: Balsa wood (I used 1/32 inch thick), diamond template (I used this one particular), printer paper, cardstock paper, X-Acto knife, goldcraftpaint, ornament hooks, super glue, screw eye hooks (13/sixteen inch).Diamond steps1. Print out your diamond template. Spot template on leading of your balsa wood and use your X-Acto knife to trace above the outline of the template to cut out your panels. two. Print an additional template on a heavier cardstock and use scissors to lower out your template. Pre-fold your template and flatten back (this can make it simpler to fold when your wood is glued on). Attach every single panel to its designated spot with super glue. three. Assemble the diamond by making use of the super glue to attach the tabs in the acceptable spots. Ahead of you glue the top piece down, make positive to screw your eye hook into the middle of the prime panel (this is what you may attach your ornament hook to). 4. Paint the diamond with the gold paint. After it truly is dry, you are prepared to hang your diamond!Diamond ornament diy abeautifulmess.com
Diamond ornament diy abeautifulmess.comIn addition to creating a handful of reliable gold diamonds, I additional a coat of glitter to some to include a minor assortment (just paint a coat of Mod Podge and sprinkle loose glitter on leading). I really like how theseornaments turned out. They add a punch of gold-plated fun to our tree, and I can tell absolutely everyone that I received loads of diamonds for Christmas. Score! xo. Laura

Credits // Writer: Laura Gummerman, Photography: Janae Hardy and Laura Gummerman

None found.

Homemade Bath BombsDaily Interior Design Ideas

Fool proof homemade bath bombs via abeautifulmess.com Easy homemade bath bombsOh yes, we went there. And man am I glad we did. I have really been enjoying “testing” these out at home. :)

Bath bombs or bath fizzes are not a new concept. I’ve seen a number of tutorials floating around the Internet, but if you’re not the DIY type, then you can just purchase pretty bath bombs (I recommend LUSH).

Easy homemade bath bombs I actually went to make some of these around Valentine’s Day last month and a couple different tutorials I tried did not produce very good results. One of them actually completely stuck to the molds and I had to chip it out with a fork so I could start over. Bummer! But hey, if at first you don’t succeed, sometimes you just have to try again.

On what I had already decided would be my final attempt, I tried this tutorial but changed up the amounts based on how many I wanted to make, and… it worked! I do have a few additionaltips if you plan to make these yourself, so check that out below. But now that I’ve found a method/recipe that works, I’m thinking I should have some friends over for a make-your-own-bath-bombs party. Added bonus: It seriously makes your whole room smell amazing while you make these!

Easy tutorial for homemade bath bombsHomemade Bath Bombs, makes two (you can easily double or triple)

4 oz. bakingsoda
2 oz. corn starch
2 oz. citric acid
2 oz. Epsom salt
1 to 1 1/2 teaspoons water
1 teaspoon essential oil
1 1/4 teaspoon oil (I like coconut or olive oil here)
1-2 drops food coloring (optional)

In a bowl combine the dry ingredients (the first four listed above). Whisk to remove any clumps, corn starch tends to be clumpy. In a small glass jar stir together the wet ingredients (the last four ingredients listed). If you’re using coconut oil, give it a quick melt in the microwave or stove top first so it will more easily combine with the other ingredients. Slowly pour the liquid mixture in with the dry mixture, whisking as you go. If you see the mixture fizz or foam, you may be adding the liquid too quickly. Once all the wet ingredients are combined with the dry, take a small amount in your hand and squeeze it together. It should stick together fairly well in one or two big chunks. If it’s still too powdery to hold together, just add a tiny bit more water and mix until it does hold together.

Then fill each half of your bath bomb mold* with the mixture until it’s just overflowing a little. Press together, then gently remove one side of the mold. Place the bath bomb on a tray and allow to dry out just a little (10-12 minutes) before removing the other side. Once you are ready to remove the other side, gently invert the bath bomb so the uncovered side is facing down, then gently remove the other half of the mold from the top. The key word, if you haven’t noticed, is gently. These can fall apart on you very easily if you’re not careful. If a bath bomb does crack in half while you’re removing it, you can gently press it back on top of the other half, or remove all the mixture back to the mixing bowl and start the molding process again. I had this happen to a few, so don’t fret, it’s easy to fix.

Once they are completely out of the mold, allow them to dry out for 8 hours or overnight. Once very dry, you can wrap them in plastic wrap and store in a dry place until you’re ready to use them, or you can gift them to friends.

*I bought my molds from Amazon. But you could also use those plastic holiday ornaments that come apart or Eastereggs for the molds if you already have either of those on hand.

In case you’re curious, the flavors I created included: lemongrass (green), lavender (purple), and peppermint (white and red).

You can add dried flower buds, like lavender buds, to these pretty easily. Just remember to use food grade dried flowers to avoid flowers that might have been grown with pesticides as you don’t want to soak in a bath with that. No thanks! Do keep in mind that after using a bath bomb with dried petals, you will have to remove these from your tub. So if that bothers you, then leave the buds out.

If you want to create two tone bath bombs, like my peppermint ones, just mix up your batter in two separate bowls and only add the food coloring to one. Easy!

These turned out to be a lot of fun to make, and they are even more fun to use! I highly recommend giving them a try, or you could make a batch to give away to friends or family. Enjoy! xo. Emma

Credits // Author and Photography: Emma Chapman. Photos edited with A Beautiful Mess actions.

Oh yes, we went there. And man am I glad we did. I have really been enjoying “testing” these out at home.

Bath bombs or bath fizzes are not a new concept. I’ve seen a number of tutorials floating around the Internet, but if you’re not the DIY type, then you can just purchase pretty bath bombs (I recommend LUSH).

I actually went to make some of these around Valentine’s Day last month and a couple different tutorials I tried did not produce very good results. One of them actually completely stuck to the molds and I had to chip it out with a fork so I could start over. Bummer! But hey, if at first you don’t succeed, sometimes you just have to try again.

On what I had already decided would be my final attempt, I tried this tutorial but changed up the amounts based on how many I wanted to make, and… it worked! I do have a few additional tips if you plan to make these yourself, so check that out below. But now that I’ve found a method/recipe that works, I’m thinking I should have some friends over for a make-your-own-bath-bombs party. Added bonus: It seriously makes your whole room smell amazing while you make these!

Homemade Bath Bombs, makes two (you can easily double or triple)

4 oz. baking soda
2 oz. corn starch
2 oz. citric acid
2 oz. Epsom salt
1 to 1 1/2 teaspoons water
1 teaspoon essential oil
1 1/4 teaspoon oil (I like coconut or olive oil here)
1-2 drops food coloring (optional)

In a bowl combine the dry ingredients (the first four listed above). Whisk to remove any clumps, corn starch tends to be clumpy. In a small glass jar stir together the wet ingredients (the last four ingredients listed). If you’re using coconut oil, give it a quick melt in the microwave or stove top first so it will more easily combine with the other ingredients. Slowly pour the liquid mixture in with the dry mixture, whisking as you go. If you see the mixture fizz or foam, you may be adding the liquid too quickly. Once all the wet ingredients are combined with the dry, take a small amount in your hand and squeeze it together. It should stick together fairly well in one or two big chunks. If it’s still too powdery to hold together, just add a tiny bit more water and mix until it does hold together.

Then fill each half of your bath bomb mold* with the mixture until it’s just overflowing a little. Press together, then gently remove one side of the mold. Place the bath bomb on a tray and allow to dry out just a little (10-12 minutes) before removing the other side. Once you are ready to remove the other side, gently invert the bath bomb so the uncovered side is facing down, then gently remove the other half of the mold from the top. The key word, if you haven’t noticed, is gently. These can fall apart on you very easily if you’re not careful. If a bath bomb does crack in half while you’re removing it, you can gently press it back on top of the other half, or remove all the mixture back to the mixing bowl and start the molding process again. I had this happen to a few, so don’t fret, it’s easy to fix.

Once they are completely out of the mold, allow them to dry out for 8 hours or overnight. Once very dry, you can wrap them in plastic wrap and store in a dry place until you’re ready to use them, or you can gift them to friends.

*I bought my molds from Amazon. But you could also use those plastic holiday ornaments that come apart or Easter eggs for the molds if you already have either of those on hand.

In case you’re curious, the flavors I created included: lemongrass (green), lavender (purple), and peppermint (white and red).

You can add dried flower buds, like lavender buds, to these pretty easily. Just remember to use food grade dried flowers to avoid flowers that might have been grown with pesticides as you don’t want to soak in a bath with that. No thanks! Do keep in mind that after using a bath bomb with dried petals, you will have to remove these from your tub. So if that bothers you, then leave the buds out.

If you want to create two tone bath bombs, like my peppermint ones, just mix up your batter in two separate bowls and only add the food coloring to one. Easy!

These turned out to be a lot of fun to make, and they are even more fun to use! I highly recommend giving them a try, or you could make a batch to give away to friends or family. Enjoy! xo. Emma

Credits // Author and Photography: Emma Chapman. Photos edited with A Beautiful Mess actions.

A Beautiful Mess App and iOS 8Daily Interior Design Ideas

Abm appThose of you who have updated your phones to iOS 8 might’ve noticed the A BeautifulMess app not showing any photos when you go to import. This is because in iOS 8, Apple decided to do away with the Camera Roll in favor of that “Moments” view that separates and groups your photos by date and a “Recently Added” folder that only shows photos from the past 30 days. The quick view in the Add Photo screen in the ABM app is tied to the Camera Roll—something that doesn’t exist on iOS 8. It’s affecting any app that defaults to the Camera Roll for its import.

We’re working on an update, but there’s a workaround in the meantime:
• On the Add Photo screen, slide up the photo selection view
• Tap the white arrow, and that should bring up all your photo folders, where you can select your photos.

It’s a couple extra steps in the meantime, but we’re actually going to expedite an update that could be up as soon as next week. So for those of you looking for another reason to procrastinate updating to iOS 8, here you go!

-Trey

P.S. If you’re having any other issues at all with iOS 8 and ABM, please email us at support AT redvelvetart DOT com. Just let us know which model of phone you’re using and be as specific as you can describing your problem.

Shadows Pendant by Dan Yeffet and Lucie Koldova for BrokisDaily Interior Design Ideas

Sparked by the imaginings of urbanlighting duo Dan Yeffet and LucieKoldova, the authentic Shadowspendant lighting collection gives you a custom seem for your modern day room. With semi-translucent glassshades and carbon stained ash wood necks, the verypresent day designer pendant lightsfromParis based designers Yeffet &amp Koldova are one thing quite specific.

Manufactured by large finish Czech lighting brand Brokis, Yeffet &amp Koldova’s latest collection of easy glass pendant lights aptly named ‘Shadows’ casts the best diffused light owing to theirblack-tinted semiopaque glass shades. The 5exclusiveshade providing allow you to produce a search as personal as you are. The Brokis Shadows collection gives modern pendant lighting for your present day area.

Posted by Keren Fathi-Bad at 12 February, 2014

Add a comment

Pleasant House With A Touch Of ShadeDaily Interior Design Ideas

Pleasant Scandinavian Home With A Touch Of Color

This stunningbrilliant and desirableScandinavianhouse located in Gothenburg, Sweden is just 70 square meters but it is nevertheless sophisticated and charming. The awesomebrick four story constructing were this apartment is located was constructed in 1890s. This apartment has a single bedroom and bathroom, a roomy residing spot, a kitchen, and a huge balcony. In the normal Scandinavian design, this house is designed with beautiful molding, smooth whitewalls, lightwoodfloors, and massive windows and doors. The white walls serve as a neutral background for vibrantaccents. Check out out some sections of this elegant apartment.

Pleasant Scandinavian Home With A Touch Of Color 2

Livingspace: A vibrant white backdrop is produced with the whites used for the ceiling, walls, doors, windows and flooring. Numerous wall photos and artwork work with black frames adorn the walls. Vividaccentcolours are employed for the beautiful chandelier. Elegant stools designed with a thin white frame and a blue top are employed in location of a coffee table. Element of the living room serves as a residenceworkplace the place a green plastic chair is employed to produce a bright accent.

Pleasant Scandinavian Home With A Touch Of Color 3Pleasant Scandinavian Home With A Touch Of Color 4

Pleasant Scandinavian Home With A Touch Of Color 5

Pleasant Scandinavian Home With A Touch Of Color 6

Pleasant Scandinavian Home With A Touch Of Color 7

Bedroom: The very same color theme is utilised in the bedroom. The red and white beddings give a sharp contrast to the white wooden headboard. Vivid normal light comes in through the huge bedroom window. Art function in black frames is utilized to decorate the plain white walls.

Pleasant Scandinavian Home With A Touch Of Color 8

Pleasant Scandinavian Home With A Touch Of Color 9

Pleasant Scandinavian Home With A Touch Of Color 10

Pleasant Scandinavian Home With A Touch Of Color 11

Kitchen: This kitchen has beautiful white cabinets and a great brown counter top. A blue hanging light fixture offers further lighting for the dining table. The black kitchen appliances contrast superbly with the white cabinets. Transparent wall cabinets with glass doors supply an stylish storage facility for kitchenware. A chic white circular table with three white chairs serves as a dining set. A number of little green potted plants are utilised to offer pretty accent colours.

Pleasant Scandinavian Home With A Touch Of Color 12

Pleasant Scandinavian Home With A Touch Of Color 13

Pleasant Scandinavian Home With A Touch Of Color 14

Pleasant Scandinavian Home With A Touch Of Color 15

Balcony: This is a colorfully decorated balcony. The color theme consists of white and shades of purple. A white classic folding outdoor table serves a coffee table. Massive pillows covered with fascinating white and purple material are positioned on the wonderful backyard chairs. A little sofa with several white and purple throw pillows completes the seating arrangement.

Pleasant Scandinavian Home With A Touch Of Color 16

Pleasant Scandinavian Home With A Touch Of Color 17

Pleasant Scandinavian Home With A Touch Of Color 18

Bathroom: Here’s a great toilet facility for the homeowner and all other day to day site visitors. It has a conventional water closet arrangement. Large white ceramic tiles and a colorful band of multi-colored tiles are employed to cover the walls. A white water closet and fundamental wash basin are put in near to the door whilst the shower is at the severe end of the bathroom. The mirror and two light bulbs set up just over the wash basin give nice lighting effects.

Pleasant Scandinavian Home With A Touch Of Color 19

Now you can share your ideas about this lovely Scandinavian home. What do you like about the design and style? What will you like to modify? How will you charge this design?

Small Residence Constructed On The Bed Of A Flatbed TrailerDaily Interior Design Ideas

by Simona Ganea , posted in Architecture, on December 5th, 2013

We’re all heard about individuals residing in trailers or in mobilehome but have you ever heard of somebody creating their home on the bed of a 24-foot extended, eight-foot wide flatbed trailer? Effectively, thisarchitect did. She built this small 196 square foot home from scratch and the produced it her dreamproperty. Since she needed the home to be sustainable, it took longer to construct it than expected, primarily due to the fact the procedure of turning recycled pallets intosiding was slow.

The architect started out this undertaking in December 2011. She developed the property whenever she had free time in amongst her perform and social routines. She employed sustainable constructingcomponents and created no compromises, even however this induced the building procedure to get longer then anticipated. As you can see, the houseseems to be like a miniature model of a standard house. It is somewhere in among classic and modern day. It has wooden exterior, a small deck and a reallywelcominginterior.

As expected, the layout is not the mostgreat choice. The house is lengthy and narrow so there’s not considerably area for hugelivingspaces. The tiny property has every little thing it demands but in smaller versions. It has a tiny kitchen, a small dining area, a function space, a sleeping spot, a bathroom and even a small deck and they all match in there.

Found on tinyhouseswoon and images by MiniMotives.

None found.

A Factory-Created Home That Looks Like Anything But Mass-ProducedDaily Interior Design Ideas

1 of the most common monikers discovered in the residencedevelopment business is “CustomHomes”. The message is simple: Allow me develop you the property that you want, not some cookie-cutter issue that lookslikeeverylittle thing else in the community.

And that appeals to us, simply because we are all exclusive folks with certain tastes that possibly don’t make a excellent match with any individual else’s. From that standpoint, we immediately rule out any house that seems to be also comparable to others. Unique homes are king.

But wait…

Going all the way back to Henry Ford, we know that a more efficient way to make things is to do them on an assembly line. We establish requirements, employees execute identical duties, and the merchandise is completed with consistent quality and value. And when we’re building a house, we really like top quality and worth. So we’re torn between asserting our persona and conserving our funds. Can this conflict be resolved?

Absolutely. Banish your image of yesteryear’s produced houses. Hunting at Texas Modular and Manufactured Homes will develop a new vision of what you can get from an assembly-line constructedhome that is something but mass-created. You can obtain a house that’s every bit as uniquely you as what the “Custom Homes” man can give you, and for substantially less money. Here’s what has took place in this industry given that you final looked.

Far better Supplies

Paneling is out, so very out. Present day modular properties feature sheetrock all through, offering better permanence, durability, and versatility of wall coverings than ever ahead of. You can paint. You can includechair rail or crown moulding. And you do not have to tolerate middle-of-the-road wallpaper.

Structurally, the residences are better too. New standards mandate that the wiring is of the very same top quality as a web site-built house, and exterior walls can be framed with 2×6 lumber rather of 2×4. Interior walls of rickety 2×2′s? A factor of the past.

Greater Option

You know you really do not want some designer whizzing down a factory line dictating cream in this room and beige in that. Manufactured homes can arrive on your web site with your decision of colors, from eggplant to rawhide and every little thing in amongst. Neutral signifies out of gear your colors can be in overdrive now.

Incredible Features

It’s not just “Single-broad or double-broad?” any longer, home-buying friend. Modular houses now include factors that were a dream in the past. Steeper roof pitches, fireplaces, porches, and dozens of other site-created functions are now just as straightforward to get from a produced residence. And simply because makers will not supply a feature they can not provide, you will avoid the complete unpleasantness of wrangling with contractors and suppliers to get the precise window or door that you want. If it’s been presented, it’s available.

Quickly, Quickly Turnaround

You can not stroll onto a greatdeal and get a internet site-developed house in a matter of weeks. Almost everything has to fall intoarea to get the home constructed on a routine. But you can walk onto a dealer’s great deal and make a buy with manufactured housing and uncover it on your property in brief buy.

Even if you purchase a customizedstyle, you are even now savingtime. It does not rain inside factories. Deliveries don’t run late, since supplies are stockpiled. Other jobs do not get in the way. You see the place we’re going. Manufactured properties are on the line nonstop through the work week, irrespective of what may possibly be beaming down from the sun or dripping down from the clouds. Simply because that line is constantly lively, your house will stay on routine for delivery without any flimsy excuses from an overbooked or under-motivated contractor.

Posted by Keren Fathi-Poor at one April, 2014

Include a comment

Playful Cabinets: NODO Furnishings Loved ones by Andrea BrugneraDaily Interior Design Ideas

NODO BUFFET CABINET AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera
Andrea Brugnera sent us photos and info about a a series of playfulcabinets entitled NODO: When I developed this loved ones of cabinets, I desired a set of container furnishings for all the space of home, with 3 basic layout features: the first is the customization, not only aesthetic but also functional the 2nd is that they had been lifted from the floor to facilitate cleaning, thanks to the authentic feet, third, the simple and clean edge is made to be assembled by the customer&#8221, explained the designer.

For these causes, the furniturefamilymembers, referred to as NODO, combinesstyle, innovation and functionality. The rope of the take care of is inserted via the door/drawers holes so you can generate a lot of variousmixture of symbols, letters or numbers. The customizable rope deal with, the fine finishing, the exact particularsthis kind of as the inclined oak feet improve the minimal line of this furniture that combines style to performance, with a contemporary character.

NODO BEDSIDE TABLE AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera

Stylish and modern, the SIDEBOARD has two swing front doors that hide the spacious compartments the place you can location pottery and tableware that you want to hold tidy and correct at hand at the very same time, in the diningspace, residing space or kitchen. The contrast between the warm oak tome of the door front and the white structure, the peculiar finishing boost the layout of this sideboard.NODO BEDSIDE TABLE STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera Stylish, capacious, contemporary the design BUFFET can easily be positioned in the dining area in buy to shop dishes, glasses, mugs and different objects or as media unit, Tv unit where you could hide the things you want, to keep a space tidy.
NODO BUFFET AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO BUFFET STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera The CABINET is component of the Nodo storagefurnishingscollection, its four spacious shelves are suitable for pottery and tableware storage, it adds an elegant, style touch to any living or dining room. The fine finishing, the accurate specifics this kind of as the inclined oak feet improve the minimum line of this cabinet that combines type and functionality.

NODO CABINET AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO CABINET DET ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO CABINET STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera The progressive design and style of the Nodo CHEST OF DRAWERS, can make it a versatile piece of furniture that can suit numerous different “interior situation”: from residing area to bedroom. It has four spacious drawers that can be personalized with codes, symbols and numbers created with the rope handles in order to determine your outfits or issues stored within. The solidity of the structure gets to be lighter thanks to the authentic touch of the inclined feet produced of solid wood.
NODO CHEST OF DRAWERS AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO CHEST OF DRAWERS STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO FOOT ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO OPEN ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO ROPE HANDLE ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera The TALLBOY, a drawer for every day of the week or a space dedicated to each and every cloth group or certain objects that you can acknowledge thanks to the symbol created with the rope handle: Seven useful drawers with four inclined oak feet and this tallboy will carry tidiness in your property!
NODO TALLBOY AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO TALLBOY STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera
The WARDROBE is element of the Nodo family members, storage furnishings with personalizable manage, merely insert the rope in the holes and design and style the blend you like. Nodo-wardrobe has two swing doors and a spacious inside compartment with coat rack. The classy feet manufactured of reliable wood that lift the construction from the floor and facilitate the floor cleaning include a touch of originality. [Data presented by means of e-mail by Andrea Brugnera Photograph Credits: Airprod | Aurelio Toscano]
NODO WARDROBE AMB ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO WARDROBE STILL ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea BrugneraNODO SYMBOLS ANDREA BRUGNERA DESIGNER FORMABILIO Playful Cabinets: NODO Furniture Family by Andrea Brugnera

You happen to be studying Playful Cabinets: NODO Furniture Lovedones by Andrea Brugnera initially posted on Freshome.

The publish Playful Cabinets: NODO Furnishings Family members by Andrea Brugnera appeared very first on Freshome.com.

Posts related to Playful Cabinets: NODO Furnishings Loved ones by Andrea Brugnera

Dynamic Details Reinforcing Originality in Contemporary Homes: Pandora Sideboard

Dynamic Details Reinforcing Originality in Contemporary Homes: Pandora Sideboard

3 Approaches To Include Surprise Colorful Particulars To Your Home

3 Approaches To Include Surprise Colorful Particulars To Your Home

20 Shoe Storage Cabinets That Are Both Functional & Stylish

20 Shoe Storage Cabinets That Are Both Functional & Stylish